How it works
- Choose a photo. The picture is scaled to fill the shape. Use Zoom and the two move sliders to choose what stays in frame.
- Pick a shape and size. Width is the printed width in millimetres; for a lamp it is the diameter and for a light box the length of one side.
- Check it backlit. The preview estimates how much light gets through each point of white PLA, so dark patches in the preview will be dark in the print. Switch to Room light to see the relief as it looks with the lamp off.
- Download and slice. The file is a closed, watertight binary STL, already standing the right way up for printing.
Which shape to choose
| Shape | Good for | Light it with |
|---|---|---|
| Flat panel | Window hangings, photo frames, the fastest first print | A window, an LED panel or strip 2–5 cm behind it |
| Curved | A desk piece that stands on its own; 90–150° is a good curve | A tea light or LED puck placed in the curve |
| Lamp (cylinder) | Lithophane lamps and shades; use “repeats” to put the photo around more than once | LED tea light, puck light or an LED bulb kit; measure your lamp base before choosing the diameter |
| Light box | A square lithophane box with the same photo, or a panorama, around four sides; open top and bottom | A tea light or puck light under it |
| Heart and circle | Gifts, ornaments, window decorations | Daylight or a small LED behind |
| Night-light panel | A lithophane night light: an arched panel with a solid tab at the bottom to slot into a plug-in LED base | A plug-in LED night-light base; set the tab thickness to its slot (often 2–3 mm) |
Best print settings
Settings matter more for a lithophane than for almost any other print, because every bit of thickness shows up as a shade of grey. These are the settings that work on ordinary FDM printers with a 0.4 mm nozzle.
| Setting | Use | Why |
|---|---|---|
| Orientation | Upright (standing on its bottom edge) for every shape except colour mode | The fine thickness changes are then traced by the nozzle path instead of being rounded to whole layers, and layer lines run across the picture where the eye hardly sees them. |
| Layer height | 0.1–0.12 mm | Upright, layer height is the vertical resolution of the picture. 0.16–0.2 mm works but shows banding. |
| Infill | 100% | Anything less leaves an infill pattern that glows through. Alternatively set 10+ walls so the slicer fills the panel with perimeters. |
| Filament | Plain white PLA | Standard or matte white gives the best contrast. Silk and glitter filaments add sheen and sparkle that fight the picture; “natural” (unpigmented) PLA is so clear that the picture washes out. |
| Speed | Outer wall 30–40 mm/s, the rest about 60 mm/s | Thin, tall walls wobble at speed, which shows as streaks. |
| Bed adhesion | A 5–8 mm brim on upright panels | A 3 mm panel standing 100 mm tall has a tiny footprint and can be knocked over by the nozzle. |
| Seam | Rear or aligned to one edge | Random seams leave dots across the picture. |
| Supports | None | None of the shapes need them. |
For a lamp, print the cylinder or light box straight up with the same settings; a brim helps here too. For a colour lithophane, print it lying face down at one fixed layer height (0.08–0.12 mm, the one you chose in the tool) and set the first layer height to the same value, not the usual 0.2 mm, or the slicer merges the first colour layers. The colour layers are cut to whole layers, so they need a flat print. The side on the bed is the viewing side.
Thickness and frame
The thinnest point becomes the brightest white and the thickest the darkest shadow. 0.8 / 3.0 mm is a sound start. Raising the minimum makes the whole print darker and safer to print; raising the maximum gives deeper blacks but needs a brighter light. The frame is a solid band at full thickness around the edge. It makes thin panels much stiffer and gives the brim something to hold, so keep 2–4 mm unless you plan to glue the panel into a frame.
Choosing a good photo
- Large subject, simple background. A face that fills a third of the frame reads well; a group of ten people at 100 mm wide turns into specks. Crop tighter with Zoom.
- Even light on the face. Harsh flash, deep shadows or a bright window behind the person all exaggerate when backlit.
- A real range from dark to light. Low-contrast or foggy photos print grey. “Stretch levels automatically” fixes mild cases; raise contrast for the rest.
- Sharp, not noisy. A phone photo is plenty (100 mm at 0.25 mm detail only needs 400 pixels across), but blur and heavy night noise show up as texture.
- Avoid big pure-white areas such as sky or a white wall. They print at minimum thickness and can look blown out; lower brightness slightly or crop them out.
Colour lithophanes
A normal lithophane only shows brightness. In colour mode the tool keeps brightness in the white lithophane and moves colour into thin filter layers. Cyan holds back red light, magenta holds back green and yellow holds back blue, so different amounts of each mix most colours. Each layer is cut to whole multiples of your layer height, so what the slicer prints matches the file, and the rounding is spread out (dithered) so skies and skin do not band.
The download is a .zip with cyan.stl, magenta.stl, yellow.stl, white.stl and a short print note (a colour the photo does not need is left out). Import all the STLs at once and keep them as parts of one object, then give each part its filament. Translucent “lithophane” CMY filament sets from Bambu Lab, Snapmaker, eSun and others give the cleanest colour. Brands differ a lot in how much light they let through, and the preview’s colours are an estimate, so print a small test with the same settings first. If the colours come out pale, raise “Max colour layer”; if they look dark or muddy, lower it.
Want a full 3D model instead of a flat lithophane?
A lithophane is a relief that only shows its picture against light. If you would rather have an object you can hold and look at from every side, try this AI generator that builds a complete mesh from a single picture, then follow our guide to checking and repairing generated models before printing.
FAQ
Is my photo uploaded anywhere?
No. The page reads the file with your browser, draws it onto a canvas and builds the mesh in a background thread on your own device. There is no upload endpoint at all: once the page has loaded you can switch off Wi-Fi and it keeps working. The STL is saved straight from memory to your downloads folder.
Is it really free? Any watermark or sign-up?
Free, with no account, no watermark and no download limit. Every shape and the colour mode are included. The files you make are yours to use; just make sure you have the rights to the photo you put in them.
What are good minimum and maximum thicknesses?
For white PLA, 0.8 mm minimum and 3.0 mm maximum is the usual starting point for prints around 100 mm. Go down to 0.6 mm for more glow if your printer handles thin areas well; go up to 3.5–4 mm for large prints or a very bright light. Keep at least 2 mm between the two, or the picture looks flat.
Why does my lithophane look dark or muddy?
Usually the maximum thickness is too high for the light behind it, the infill was not 100%, or the filament is a dense “bright white”. Try a stronger or closer LED, print a little thinner, and check the slicer shows solid plastic throughout. If only the shadows are muddy, raise brightness a little or switch the tone curve to Light-true.
What is the Light-true tone curve?
Light fades roughly exponentially as it passes through plastic, so thickness that rises in equal steps does not give brightness in equal steps. Light-true works backwards: it takes the brightness each point of the photo should have and picks the thickness of white PLA that lets about that much light through. Linear is the classic straight mapping, which lifts shadows and darkens highlights a little. The backlit preview uses the same light model for both, so you can compare them there.
How does the colour lithophane mode work?
It splits the photo into a white lithophane, which carries brightness, and thin filter layers in cyan, magenta and yellow, which carry the colour. You get one STL per filament plus a print note, all lined up so the slicer loads them as parts of one object. You need a printer that switches filaments by itself (Bambu AMS, Prusa MMU, Creality CFS, a toolchanger): the colours change within each layer, so manual filament swaps do not work. It prints lying flat at one fixed layer height, first layer included.
Which light should I use?
LEDs only. PLA starts to soften around 55–60 °C, so incandescent and halogen bulbs can warp a lamp shade. A warm white (2700–3000 K) LED gives the classic look; a neutral 4000 K LED shows more detail. For lamps and light boxes a battery tea light or a USB puck light works; for a flat panel, an LED strip or panel 2–5 cm behind it lights it evenly.
Can I print it on a resin printer?
Yes. Resins differ far more than PLA in how much light they let through, so print a small test strip with a few thicknesses first and set the minimum and maximum from that. No hollowing is needed; the parts are already thin.
Why is the STL so big?
A lithophane is a dense surface: every 0.25 mm point of the picture is a vertex. A 100 × 75 mm panel at Fine detail is around 25 MB, which slicers handle easily. Use Standard (0.3 mm) or Draft for big lamps or if your slicer struggles. Finer than 0.25 mm only pays off with a 0.2–0.25 mm nozzle. On phones the tool lowers the detail of very large prints so the browser does not run out of memory.